







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Delta Bathroom Remodeling in Santa Clarita: What to Know First
Independent Delta bathroom remodeling in Santa Clarita typically runs $9,000 – $28,000 for a full remodel and $4,500 – $12,000 for a walk-in shower, with most projects taking two to four weeks once the fixtures and tile are on hand. We’re an independent Delta service provider, not affiliated with or authorized by Delta, and we quote a written price before any work starts so the number you approve is the number on the invoice. We’re Penhallow Remodeling Santa Clarita, and we work on Delta faucets, valves, shower systems and fixtures every week.
This page is for Santa Clarita homeowners whose Delta fixtures are at the center of a bigger job: a tub-to-shower conversion, a full bathroom remodel, or a vanity-and-fixture refresh. If you’re deciding between repairing one failing item and remodeling the whole room, this is where to start. Call (866) 383-6693 for a free estimate.
How Delta Products Fail – and How We Fix Them
Delta gear shows up in a lot of Santa Clarita bathrooms, and its failure modes differ from the no-name imports. Here’s what we see most often, and what we do about it.
- Monitor 14 and Monitor 17 shower valves that won’t hold temperature. The pressure-balancing spool inside these valves wears or gets mineral-fouled, so the water swings hot-cold when someone flushes a toilet. It’s the cartridge assembly, not the trim most people replace. We swap the internal balancing cartridge with the correct OEM part and test under a real simultaneous-flow load, because a valve that passes with no toilet flushing can still scald you at 7 a.m. That same behavior shows up across Santa Clarita, where our water runs hard and mineral-heavy, and it’s the quiet cause behind dozens of “the shower is possessed” calls.
- Touch-Clean showerheads and hand-shower heads clogging at the spray face. Calcium scale builds in the rubber nozzles over time, and because the nozzles are designed to be rubbed clean, homeowners often scrub until a nozzle tears or the flow restrictor clogs behind it. We inspect the spray face and the flow restrictor, clean or replace the head, and check the elbow screen where sediment collects. A customer in Saugus told us her head “spits sideways” for two years, which turned out to be a cracked nozzle rubber, not a pressure problem.
- Traditional dual-handle and single-handle lavatory faucets that drip from the spout. That’s usually the seat-and-spring or the cartridge, and on older Delta models it’s a genuinely cheap fix, not a faucet replacement. The stronger play, though, is to match the faucet to the vanity material when the whole room is coming out anyway. We routinely pair Delta with a Cambria or Silestone quartz top with a molded sink rather than an undermount, since an undermount on a real stone top is a cleaner look when it’s a full remodel.
- In2ition two-in-one systems that leak at the diverter. The magnetic dock and the diverter inside the body are the weak points when hard water is present, and a dock that won’t grab means the handheld falls to a tile floor. We replace the diverter cartridge and the docking magnet assembly, and where the shower is getting new tile, we set a proper backing and cement board substrate (the moisture-resistant layer behind the tile) so a re-leak at the valve doesn’t send water into the wall cavity.
- Delta shower pans and assembled surrounds that outlive their caulk. In Santa Clarita, the reality is hot, dry summers and a sharp swing to cooler nights, and that day-to-night movement works on expansion joints and silicone around a pan or wall seams. Caulk dries and pulls, water sneaks behind, and the wall board behind it gets soft. On a remodel we pull the surround, inspect the substrate, and rebuild with a waterproofed pan and a tile or engineered-panel finish that has room for the movement.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Our Delta Bathroom Remodeling Process
Here’s how a Delta job actually runs from your first call to the day we pack up.
- 1
The call and the written price. A live person answers, we ask what’s failing and what you want changed, and we set a real arrival window. You get a written price before any work starts, not a verbal ballpark.
- 2
Diagnostics on site. We open the valve, check the cartridges and O-rings, test the spray patterns, and look at the substrate behind the surround where it’s accessible. We tell you which Delta parts are involved and what they cost.
- 3
The parts decision. In most cases we use genuine Delta OEM cartridges and trim because the finish and seat are matched to the housing. On discontinued models we can sometimes use a quality aftermarket equivalent and tell you plainly that it won’t carry the same match. We don’t put an aftermarket cartridge in a valve that’s still under a manufacturer warranty without telling you it could affect a future claim.
- 4
The remodel proper. Demo to the studs where needed, new cement board substrate, waterproofing, then tile and Delta fixtures set and sealed.
- 5
The test. Hot-cold swing under flow, leak test at every joint, spray test on the shower, and a full-function check before we sign off.
- 6
The guarantee and cleanup. Every project is covered in writing by our 365-Day Done Right Promise, and the job site is left cleaner than we found it.
What Delta Bathroom Remodeling Costs in Santa Clarita

Real ranges, not “prices vary.” Here’s what common Delta bathroom jobs run around Santa Clarita.
- Full bathroom remodel: $9,000 – $28,000, depending on layout, tile, vanity cabinetry and material.
- Walk-in shower installation or shower remodel: $4,500 – $12,000.
- Tub-to-shower conversion: $3,500 – $10,000.
- Small bathroom remodel: $5,000 – $12,000.
- Bathroom vanity installation: $800 – $3,000 (Delta faucet and fixtures included in scope).
What moves the number: whether we’re moving the drain or keeping the plumbing rough-in in place, the tile and stone you pick, whether you’re keeping the Delta valve body or swapping it, and whether the substrate behind the wall needs rebuilding. A single failing Delta cartridge is a repair; a failing valve behind tile in a 20-year-old room is usually the cue for a remodel. Call (866) 383-6693 for an exact quote. Estimates are free, and the price comes in writing.
See the difference
Before
After
Before
After
Before
AfterWhy Santa Clarita Homeowners Call Penhallow Remodeling Santa Clarita for Delta Work
The work is backed by our 365-Day Done Right Promise: if it fails inside the year, we come back and fix it at no charge, and that’s in writing. A live person answers the phone 24/7, so you’re not leaving a voicemail and hoping. Our technicians have up to 22 years of experience and arrive background-checked and in uniform, so you know who’s in the room.
We know Delta trim and cartridge families well enough to tell a valve-body problem from a trim problem before we start tearing out tile. And when the remodel reaches beyond Delta, we’re comfortable sourcing the other parts from brands we trust: KraftMaid cabinetry, Kohler and Toto fixtures, Cambria quartz, and Moen where it fits. We’re part of the Kingswell family of companies, operating to The Kingswell Way: say the price before the work, show up in the window we gave, leave the place cleaner than we found it. We’re independently owned and operated.
Frequently Asked Questions

No. We’re an independent Delta service provider, not authorized, sponsored or affiliated with Delta. We install and work on Delta fixtures, but we’re a remodeling general contractor and the manufacturer doesn’t endorse us or our work. If you have a warranty question about a Delta part itself, that’s between you and Delta. Call (866) 383-6693 for a free estimate on the remodel side.
Yes, we can get genuine Delta cartridges, trim and repair parts for most current and older model lines, and on most jobs the OEM part is the right call because the seat and finish are matched to the valve housing. Aftermarket equivalents exist and are cheaper, but they can fail differently and may not match the finish, so we tell you the trade-off before we install one. Call (866) 383-6693 for a free estimate.
Usually it’s the pressure-balancing cartridge inside the valve, and that part is replaceable without tearing the wall on most Delta Monitor installations, so repair is often the smart first move. If the valve body itself is corroded or you’re already planning a tub-to-shower conversion, swapping the whole valve during the remodel is cleaner than paying to repair it twice. We’ll tell you which situation you’re in on site. Call (866) 383-6693 for a free estimate.
A full bathroom remodel typically takes two to four weeks once materials are on site; a walk-in shower install or a tub-to-shower conversion often runs one to two weeks. The schedule depends on tile lead time, whether we’re moving plumbing, and how much substrate repair the room needs. We give you a written price and a real arrival window before work starts. Call (866) 383-6693 for a free estimate.
Installation done to Delta’s specs shouldn’t void a product warranty, and we install to the manufacturer’s requirements and keep the paperwork you’ll need if you ever file a claim. The thing that catches homeowners is a warranty claim against a part we didn’t install or an aftermarket part swapped in during a previous repair, so we check what’s actually in the wall first. Call (866) 383-6693 for a free estimate.
Written by the team at Penhallow Remodeling Santa Clarita, serving Santa Clarita and nearby areas.
Ready to Price Your Delta Bathroom Remodel?
Call (866) 383-6693 and a real person answers, day or night. We’ll set a real arrival window, diagnose the Delta fixtures in the room, and put a written price in your hands before a single tile comes up or a single cabinet is pulled. Estimates are free.












